Victron SmartSolar 100/30 - 100/50 12/24V MPPT Controller View full size

Victron SmartSolar 100/30 - 100/50 12/24V MPPT Controller

Victron energy

278,30 € tax incl.

Options

Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.

logo victron energy

More details

More info

Victron

Ultra-fast Maximum Power Point Tracking (MPPT)

 

Especially in case of a clouded sky, when light intensity is changing continuously, an ultra-fast MPPT controller will improve energy harvest by up to 30% compared to PWM charge controllers and by up to 10% compared to slower MPPT controllers.


Advanced Maximum Power Point Detection in case of partial shading conditions

 

If partial shading occurs, two or more maximum power points may be present on the power-voltage curve.
Conventional MPPTs tend to lock to a local MPP, which may not be the optimum MPP. The innovative SmartSolar algorithm will always maximize energy harvest by locking to the optimum MPP.


Outstanding conversion efficiency

 

No cooling fan. Maximum efficiency exceeds 99%.


PV voltage up to 100V

 

The charge controller is able to charge a lower nominal-voltage battery from a higher nominal voltage PV array. The controller will automatically adjust to a 12 or 24V nominal battery voltage.


Flexible charge algorithm

 

Fully programmable charge algorithm (see the software page on our website), and eight pre-programmed algorithms, selectable with a rotary switch (see manual for details).


Extensive electronic protection

 

Over-temperature protection and power derating when temperature is high. PV short circuit and PV reverse polarity protection. PV reverse current protection.


Internal temperature sensor

 

Compensates absorption and float charge voltage for temperature.


Adaptive three step charging

 

The Controller is configured for a three step charging process: Bulk – Absorption – Float.

Bulk
During this stage the controller delivers as much charge current as possible to rapidly recharge the batteries.

Absorption
When the battery voltage reaches the absorption voltage setting, the controller switches to constant voltage mode. When only shallow discharges occur the absorption time is kept short in order to prevent overcharging of the battery. After a deep discharge the absorption time is automatically increased to make sure that the battery is completely recharged. Additionally, the absorption period is also ended when the charge current decreases to less than 2A.

Float
During this stage, float voltage is applied to the battery to maintain it in a fully charged state. When the battery voltage drops below float voltage during at least 1 minute a new charge cycle will be triggered.


VE.Direct

 

For a wired data connection to a Color Control panel, PC or other devices

Remote on-off

 

To connect for example to a VE.BUS BMS.


Automatic battery voltage recognition

 

The controller will automatically adjust itself to a 12V or a 24V system one time only. If a different system voltage is required at a later stage, it must be changed manually, for example with the Bluetooth app.

 

 

SmartSolar Charge ControllerMPPT 100/30MPPT 100/50
Battery voltage12/24V Auto Select
Rated charge current30A50A
Nominal PV power, 12V 1a,b)440W700W
Nominal PV power, 24V 1a,b)880W1400W
Maximum PV open circuit voltage100V
Max. PV short circuit current 2)35A60A
Maximum efficiency98%
Self-consumption10 mA
Charge voltage 'absorption'Default setting: 14,4V / 28,8V / 57,6V (adjustable)
Charge voltage ‘equalization’ 3)Default setting: 16,2V / 28,8V / 64,8V (adjustable)
Charge voltage 'float'Default setting: 13,8V / 27,6V / 55,2V (adjustable)
Charge algorithmmulti-stage adaptive (eight preprogrammed algorithms) or user defined algrithm
Temperature compensation-16 mV / °C resp. -32 mV / °C
ProtectionBattery reverse polarity (fuse, not user accessible)
Output short circuit, Over temperature
Operating temperature-30 to +60°C (full rated output up to 40°C)
Humidity95%, non-condensing
Maximum altitude5000m (full rated output up to 2000m)
Environmental conditionIndoor type 1, unconditioned
Pollution degreePD3
Data communication portBluetooth and VE.Direct
ENCLOSURE
ColourBlue (RAL 5012)
Power terminals13 mm² / AWG6
Protection category

IP43 (electronic components),
IP22(connection area)

Weight1,25 kg
Dimensions (h x w x d)130 x 186 x 70 mm
STANDARDS
SafetyEN/IEC 62109-1
1a) If more PV power is connected, the controller will limit input power.
1b) The PV voltage must exceed Vbat + 5V for the controller to start. Thereafter the minimum PV voltage is Vbat + 1V.
2) A higher sort circuit current may damage the controller in case of reverse polarity connection of the PV array.
3) Default setting: OFF

Specifications

Charge power30A, 50A

Data sheets and documentation

Product Reviews
  • Number of Reviews : 2
  • Average Grade : 4.5 /5
  • S. Herve
  •  the 07/06/2018
  • 4/5
Semble en ordre, a vérifier.
  • P. Gerhard
  •  the 31/03/2018
  • 5/5
Premier choix